These Kits will be for the 8mm Stud kit, most of us are running a Cool Dome that requires the 10mm base/8mm top (these will be in the store sometime soon)
Just waiting on the copper washers to arrive, these Acorn Nuts have the smooth base, flanged, and taller, and plated with the most important factor with the 12mm heads. If you ever used the 13mm Acorn Nuts they are a PIA to tighten.
The 6 stud and a 7 stud kits will be around $15.00 with the 7 stud kit slightly higher plus shipping (Flat Rate $5.95).
The Cool Domes O ring Kits will be out soon they will include the upper dome o rings the dome O ring and the outer dome ring.
Like to hear you thoughts
I like those.... so now you don't need to ultra grey the studs?
I like to see the sqhq store continue to expand its product line.
How about adding some Voodoo fliptop kits Mitch?
So these are only usable with a coolhead? The acorn nuts and washers I mean.
No you can use these with any head.... Good stuff 12 mm and not 13 mm
Look at that sloppy sealant job all over the cylinder!
Gross, man.
Look at that sloppy sealant job all over the cylinder!
Gross, man.
Tudors likes to use lots of his sealant........... Good thing Im O ring this dome
Is around $15 gonna include nuts and copper washers?
Is around $15 gonna include nuts and copper washers?
YES for the 6 stud Kit. Also confirming if these will also work on the LT250s
So about $18 for a 7 stud kit then + the shipping?
Doing some changes, having to have custom copper washers being made in so doing the math on the 6 Stud Kit $23.95 (6 Plated Nuts and 6 Washers) and the 7 Stud Kit $27.95 (7 Plated Nuts and 7 Copper Washers)"SHIPPED" USA 48 States, them other 2 states e mail for a quote.
SHIPPED PRIORITY MAIL -average of 2 to 3 days for delivery .
Washers are .040" thick x 16mm OD x 8.4mm ID #110 Alloy Half Hard
Acorn Nuts are Plated & Flanged, 16.75mm Flanged Base -Smooth Bottom X 16.50mm tall, Head Size is 12mm (Wrench Size) 15.90mm deep.
Mitch, i'm not too sure on them fitting the 250. I think my 250 had smaller diameter studs if I can remember correctly. But I might be down for a 6 stud set pretty soon.
Mitch, i'm not too sure on them fitting the 250. I think my 250 had smaller diameter studs if I can remember correctly. But I might be down for a 6 stud set pretty soon. 
Figured they were like the Honda Head Studs 8mm
need to get that lt250r running el diablo my tri z is getting ready to play with another baby zilla!
need to get that lt250r running el diablo my tri z is getting ready to play with another baby zilla! 
It's in good hands right now.
cant wait to see it back in action, i curious about the top end that was "donated" by our good friend chris
Mitch pencil me in for a 7 stud set!
need to get that lt250r running el diablo my tri z is getting ready to play with another baby zilla! 
It's in good hands right now. 
I know which hands it is in for some R and D!! Yes it is in good hands.
why would't they fit a lt250? there 8X1.25 thread. same thread as a zilla head studs. same as a 250r, triz, tecate i could go on. lt250r has acouple m6 studs for the cylinder.
why wouldn't they fit a lt250? there 8X1.25 thread. same thread as a zilla head studs. same as a 250r, triz, tecate i could go on. lt250r has acouple m6 studs for the cylinder.
That's probably what I was thinking. Either that or my zilla has bigger head studs?
need to get that lt250r running el diablo my tri z is getting ready to play with another baby zilla! 
It's in good hands right now. 
I know which hands it is in for some R and D!! Yes it is in good hands.
As I like to say, Rome wasn't built in a day. Good things take time.
As I like to say, Rome wasn't built in a day. Good things take time.
I don't think Detroit was built in a day either.
I hear it's not a fun place to be.
I don't think Detroit was built in a day either.
I hear it's not a fun place to be.
I've been there. Almost all of Detroit is a chit hole. That's what happens when liberals run a city.