+-
« previous next »
Pages: [1]   Go Down

Author Topic: with what should i use paul turner or fmf  (Read 831 times)

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
with what should i use paul turner or fmf
« on: May 21, 2013, 07:10:06 pm »
 The fmf looks better all shiny and stuff sounds good to but  the Paul turner pipe got the surface rust going on I know looks ant ever thing lol because u should see some of the women I dated just wanna know what one should I use and if I got to er jet the carb to run the Paul tunner 2c
Logged

Share on Bluesky Share on Facebook

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #1 on: May 21, 2013, 07:14:51 pm »
Pic of the too pipe
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #2 on: May 21, 2013, 07:16:22 pm »
Pics
Logged

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 474
  • Gender: Male
  • 2 stroke or no stroke
  • Location: Minnesota
Re: with what should i use paul turner or fmf
« Reply #3 on: May 21, 2013, 07:16:37 pm »
the paul turner is a better pipe
Logged
89 zilla Bartlett racing Dune Porting,42.5mm rx'd carb,DrQ pipe, vf3 reeds
 89 lt250r custom frame with Bartlett racin Dune Porting, DR Q pipe, zilla carb, vf3 reeds
 00 426ex 12:5 comp, stage2 cam, full yosh exauast, +2+1 a arms, +2 lons

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #4 on: May 21, 2013, 07:18:54 pm »
Pics
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #5 on: May 21, 2013, 07:24:41 pm »
What about er jeting the card for the Paul turnner or is it not necessary ?? I got to take the fmf off any way lol for got to use gasket sealer on the pipe so I got will oil over my motor
Logged

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 474
  • Gender: Male
  • 2 stroke or no stroke
  • Location: Minnesota
Re: with what should i use paul turner or fmf
« Reply #6 on: May 21, 2013, 07:29:18 pm »
you will to jet it. it should not be that fare off from the fmf. put it on and do a plug chop and see where its at
Logged
89 zilla Bartlett racing Dune Porting,42.5mm rx'd carb,DrQ pipe, vf3 reeds
 89 lt250r custom frame with Bartlett racin Dune Porting, DR Q pipe, zilla carb, vf3 reeds
 00 426ex 12:5 comp, stage2 cam, full yosh exauast, +2+1 a arms, +2 lons

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #7 on: May 21, 2013, 07:35:01 pm »
I did not get what u was trying to say?
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #8 on: May 21, 2013, 07:44:05 pm »
Pics of plug after 1 day of heat cycles and ran it up and down the road just putting lol fmf front to back
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #9 on: May 21, 2013, 07:45:56 pm »
Plug number is b8egv
Logged

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 474
  • Gender: Male
  • 2 stroke or no stroke
  • Location: Minnesota
Re: with what should i use paul turner or fmf
« Reply #10 on: May 21, 2013, 08:05:28 pm »
put the paul turner pipe on and run it and wide open then look at the plug it should be a light brown. if not it has to be jetted. dark brown means to rich white is to lean
Logged
89 zilla Bartlett racing Dune Porting,42.5mm rx'd carb,DrQ pipe, vf3 reeds
 89 lt250r custom frame with Bartlett racin Dune Porting, DR Q pipe, zilla carb, vf3 reeds
 00 426ex 12:5 comp, stage2 cam, full yosh exauast, +2+1 a arms, +2 lons

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #11 on: May 21, 2013, 08:14:02 pm »
Here the deal with the Paul pipe it came off a parts bike that **** the jug on both sides and the cooling got in to the pipe so it has rust clumps in side the pipe that comes off the jug will that hurt my 500 and the pipe has brackets welded to it so how would if  it's a Paul turnner
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 41
Re: with what should i use paul turner or fmf
« Reply #12 on: May 21, 2013, 08:15:46 pm »
Pics of pipe
Logged

Offline

  • Trade Count: (0)
  • Forum Moderator
  • Elite Member
  • *********
  • Posts: 2058
Re: with what should i use paul turner or fmf
« Reply #13 on: May 21, 2013, 08:27:34 pm »
That rust shouldn't be a problem unless its rusting thru....

If you get some muratic acid from Home Depot that nasty smelling caustic dangerous liquid will take that rust right off, if you seize your piston and your bore has aluminum transferred onto the cylinder walls that acid will take the aluminum right off and leave the steel liner in useable condition. Pool supply has it too.
Logged
87 HPR LT500
04 Roll LOBO II TRX250R
06 LTR450
87 LT500
85 & 86 LT250
86 & 87 TRX250R
07 & 09 Husqvarna TE450
00 CR125R
Pages: [1]   Go Up
« previous next »
 

+- Suzuki Quadracer HQ Store Zone

http://www.suzukiquadracerhq.com/index.php?action=store