+-
« previous next »
Pages: [1]   Go Down

Author Topic: lt250r re sleeved  (Read 621 times)

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
lt250r re sleeved
« on: March 26, 2013, 04:25:33 pm »
well i disassembled the top end of my 250 to refreshin and to do the rm bearing and hd washers, i found the cylinder had been resleeved and is on stock bore.. i noticed in the boost ports the aluminum is just about gone on the inside of the ports towards sleeve??? has anyone seen this?
Logged

Share on Bluesky Share on Facebook

Offline

  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 261
Re: lt250r re sleeved
« Reply #1 on: March 26, 2013, 04:47:49 pm »
Does it look like the cylinder was ported before it was resleeved? If so, the sleeve needs to be matched. A pic of what your talking about may help.
Logged
Success only come before work in the dictionary.

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
Re: lt250r re sleeved
« Reply #2 on: March 26, 2013, 05:40:13 pm »
no it doesnt look ported, it looks like the sleeve was thicker outer diameter then the stocker and they bored the alumunum casting bigger or something, the inside of the boost ports are against the sleeve, no aluminum left.. il try getn picks tomorrow
Logged

Offline

  • Trade Count: (0)
  • Pro Member
  • ********
  • Posts: 853
  • Gender: Male
  • Location: Chatam NY Upstate
Re: lt250r re sleeved
« Reply #3 on: March 26, 2013, 05:47:38 pm »
Get some measurements too. Bore ID and Sleeve OD.
Logged
92 LT250R- Bartlett racing prototype big bore. Wide, Low,  and studded

91 LT250R Mickey Thompson stadium racer

87 LT500R- Mostly stock

89 LT500R IceZilla, mods TBA

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
Re: lt250r re sleeved
« Reply #4 on: March 27, 2013, 02:13:22 pm »
The bore was stock at67, od is 77.50
Logged

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
Re: lt250r re sleeved
« Reply #5 on: March 27, 2013, 02:16:51 pm »
my phones crap sorry, i think u can see the issue though <1>
Logged

Offline

  • CEO BRP
  • Trade Count: (0)
  • Trail Blazer
  • ******
  • Posts: 772
  • BRaP Small block 302, Released and Running
Re: lt250r re sleeved
« Reply #6 on: March 27, 2013, 02:21:54 pm »
Ya that's pretty standard.
Logged

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
Re: lt250r re sleeved
« Reply #7 on: March 27, 2013, 02:23:32 pm »
so is it ok to run??   D?
Logged

Offline

  • CEO BRP
  • Trade Count: (0)
  • Trail Blazer
  • ******
  • Posts: 772
  • BRaP Small block 302, Released and Running
Re: lt250r re sleeved
« Reply #8 on: March 27, 2013, 03:12:59 pm »
Yup pretty typical of any sleeved cylinder.
Logged
Pages: [1]   Go Up
« previous next »
 

+- Suzuki Quadracer HQ Store Zone

http://www.suzukiquadracerhq.com/index.php?action=store