-
-
Hey guys I was riding yesterday and lost my rear brake when I got back I noticed the circlip had come out I got it back in but I still have no brakes I'm not leaking any fluid and the brake pedal returns but its just not biting the disc I opened up the bleeder and I'm getting fluid out of it any ideas??
-
-
#1 Reply
Posted by
GrkGuy
on 14 Jan, 2013 16:55
-
has to be a air pocket, crack each fitting and check for air
-
-
-
I was thinking that but I was also thinking my piston might be frozen because I can't get it to move at all the inside pad is just about against the rotor maybe 1/16 from it
-
-
-
Also would air being in there prevent the piston from open and closing?
-
-
#4 Reply
Posted by
GrkGuy
on 16 Jan, 2013 13:54
-
thats what i was thinking, fill rezzy and bleed it again
-
-
#5 Reply
Posted by
Stpltn250r
on 16 Jan, 2013 14:49
-
I ran into the same problem but my rakes were locking up after being applied a few times. When I went to bleed off the fluid with the caliper it freed up until the next few times with the brake being applied. I have been told the bleed valve in the brake rezzy is funked up. Not allowing the pressure or fluid bleed back into the cup when the brake is not applied.
-
-
-
Well the rezzy is still full should I bleed it all out and then refill it? And when I'm bleeding them I pump them up but it goes all the way down everytime is it supposed to do that cuz I know with a car you will have some petal left an when u open the bleeder it releases to the floor
-
-
#7 Reply
Posted by
GrkGuy
on 16 Jan, 2013 15:40
-
you have air in it then if it is not getting hard. check all banjo bolts to be clean. the get crud in them
if the fluid is old, then try bleeding master cylinder first, crack banjo bolt with pressure on the brake.
then work your way back to caliaper
-
-
-
Where is the banjo bolt?
-
-
-
Is that the one that holds the brake line on the caliper? And you said bolts is there another one on the other side of the brake line opposite of the caliper
-
-
#10 Reply
Posted by
Dezsled
on 16 Jan, 2013 15:50
-
There two of them one on the master cylinder/lever ass. and one on the caliper. The banjo bolt is the bolt that connects the brake line to the master cyl and caliper.
-
-
-
K so I should start with the one on the master cyl first then the caliper right?
-
-
#12 Reply
Posted by
Dezsled
on 16 Jan, 2013 16:00
-
Yes. If your fluid is old try to bleed in fresh fluid. It will take time to do this but when your done lever 'feel' will be firmer.
-
-
-
I
**** both with pedal down and got nothing no air or fluid which is weird because I'm getting fluid at the bleeder
-
-
#14 Reply
Posted by
GrkGuy
on 16 Jan, 2013 17:13
-
bleeder is cavity locked, you need to get fluid into master cylinder, crack the banjo bolt and see if any fluid will start to drain out.
-
-
-
-->I don't understand the caliper must be getting fluid if when I crack the bleeder and push the pedal down it comes out
-
-
-
How do I get fluid into the master I pumped the brake and
**** the banjo on it and got nothing do I need to completely remove the bolt
-
-
#17 Reply
Posted by
GrkGuy
on 16 Jan, 2013 18:43
-
just crack the banjo or remove it, the one on the master, till fluid starts to come out on its own, if master is full it should
start to gravity feed out, once its coming out tighten back up then pump the brake a few times then bleed caliaper again
-
-
#18 Reply
Posted by
Dezsled
on 16 Jan, 2013 19:24
-
-
-
-
Should I do the same on the banjo on the caliper before I bleed it?
-
-
#20 Reply
Posted by
GrkGuy
on 16 Jan, 2013 21:57
-
i would do it to all of them till you see fluid come out
-
-
-
Ok thanks a lot guys ur the best this forum is awesome id be lost without it
-
-
-
Yup you guys were right
**** the banjos and bled it after works great I was trying to hook up some after market fog lights but when I wire them up they are very dim untill I give it throttle anyone know why it would do this?
-
-
#23 Reply
Posted by
El Diablo
on 17 Jan, 2013 12:28
-
Check your voltage at Idle. You might only be putting out 8 or 9 volts at idle speed. Also, what is the wattage of each fog light & how many are you using? What Ga wire are you running?
-
-
-
Where should I check it I wanted to run 2 but even just the one is doing it
-