+-
« previous next »
Pages: [1]   Go Down

Author Topic: I can't believe people- NO THRUST WASHERS!  (Read 863 times)

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
I can't believe people- NO THRUST WASHERS!
« on: September 27, 2013, 04:41:29 pm »
Got around to putting my 500 back together and noticed there were no thrust washers in the crank or piston. I am at a loss for words.
Is a special tool required to split the cases? How bad is it that these parts are missing?

I am referring to number 6 & 9



Thanks
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/

Share on Bluesky Share on Facebook

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
Re: I can't believe people- NO THRUST WASHERS!
« Reply #1 on: September 27, 2013, 04:53:01 pm »
There were none that I could see; and the piston moved back and forth as did the crank.
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/

Offline

  • 1991 Lt250r
  • Trade Count: (0)
  • Elite Member
  • **********
  • Posts: 1350
  • Gender: Male
  • Location: West Virginia
Re: I can't believe people- NO THRUST WASHERS!
« Reply #2 on: September 27, 2013, 04:55:38 pm »
Sometimes they are hard to see got any pics
Logged
91 Lt250r Bartlett port and head mod v force 2 Hinson Clutch Basket Cool Head Scp Pipe and silencer ,KN air filter ,EBC clutch, Ohlins  Triple rate Shocks Redone by PEP Shocks,Stock Rear Shock Redone By Pep Shock,  DG nerf Bars , Lonestar axle 2+2,Lonestar Swingarm ,Douglas Red Label rims.

Offline

  • Trade Count: (0)
  • Pro Member
  • ********
  • Posts: 858
Re: I can't believe people- NO THRUST WASHERS!
« Reply #3 on: September 27, 2013, 04:59:18 pm »
Part # 9 is probably there but you cannot usually see it unless you push the OEM rod to the extreme left or right to see it. Part # 9 has the same outside diameter as the rod bearing and sometimes runs inside the edge of the con rod where it is difficult to see.   If you have a Hot Rod, I do not think that Hot Rod uses Part # 9
Logged

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
Re: I can't believe people- NO THRUST WASHERS!
« Reply #4 on: September 27, 2013, 05:11:04 pm »
Here are some pcis. Pardon my terrible camera.
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/

Offline

  • Trade Count: (0)
  • Pro Member
  • ********
  • Posts: 984
  • Gender: Male
  • Location: Detroit, mi
Re: I can't believe people- NO THRUST WASHERS!
« Reply #5 on: September 27, 2013, 05:46:48 pm »
I panicked about my crank also as it will move side to side but that is normal. They are probably there.

The piston wrist pin however does need them.
Logged
Ain't ever seen it......but I have heard it.

Offline

  • Trade Count: (0)
  • Pro Member
  • ********
  • Posts: 984
  • Gender: Male
  • Location: Detroit, mi
Re: I can't believe people- NO THRUST WASHERS!
« Reply #6 on: September 27, 2013, 05:48:52 pm »
You can see the crank washers. They are definitely missing on the piston. 
Logged
Ain't ever seen it......but I have heard it.

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
Re: I can't believe people- NO THRUST WASHERS!
« Reply #7 on: September 27, 2013, 05:54:57 pm »
MotorGeek, do the billet ones you sell fit a 500?
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/

Offline

  • Trade Count: (0)
  • Pro Member
  • ********
  • Posts: 984
  • Gender: Male
  • Location: Detroit, mi
Re: I can't believe people- NO THRUST WASHERS!
« Reply #8 on: September 27, 2013, 06:12:55 pm »
Yeah HPR has 500 Billet Washers. I just installed some. Good price too.  (Y)
Logged
Ain't ever seen it......but I have heard it.

Offline

  • Trade Count: (0)
  • Elite Member
  • **********
  • Posts: 1287
  • Location: Ontario,Great White North
Re: I can't believe people- NO THRUST WASHERS!
« Reply #9 on: September 27, 2013, 07:25:41 pm »
x2 on the HPR washers,he even sells ya the RM bearing too.
Logged
Can,t fix stupid.:)

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
Re: I can't believe people- NO THRUST WASHERS!
« Reply #10 on: September 27, 2013, 10:33:29 pm »
The RM bearing applies to 500s too?
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/

Offline

  • Trade Count: (0)
  • Forum Moderator
  • Pro Member
  • *********
  • Posts: 970
Re: I can't believe people- NO THRUST WASHERS!
« Reply #11 on: September 28, 2013, 12:44:34 am »
Yes they do, i ordered a set for my friends 500 but got then from mitch, the super forum moderator.
Logged
1985 Yamaha Tri Z 250
2006 Suzuki LTR 450
2011 Suzuki Hayabusa

Offline

  • Major Bell End
  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 185
  • Gender: Male
  • Ayeeee
  • Location: South of Boston
Re: I can't believe people- NO THRUST WASHERS!
« Reply #12 on: September 29, 2013, 08:37:08 pm »
Link to purchase?
Logged
Read me; you'll probably regret it
http://oneguytwowheels.blogspot.com/
Pages: [1]   Go Up
« previous next »
 

+- Suzuki Quadracer HQ Store Zone

http://www.suzukiquadracerhq.com/index.php?action=store