+-
« previous next »
Pages: [1]   Go Down

Author Topic: Interest On Making OEM Type Front Bumpers  (Read 804 times)

Offline

  • Mitch Keller
  • Trade Count: (0)
  • Administrator
  • Trail Blazer
  • *****
  • Posts: 799
  • Love The Smell Of 927 and Race Fuel In The Morning
  • Location: Riverside Ca
Interest On Making OEM Type Front Bumpers
« on: January 31, 2013, 11:17:20 am »
I want another Fat Bar Front Bumper, and they want almost $70 bucks with shipping, not counting the plating cost, so I am looking into getting some bids on making 10 of these, also having a few sets made with light bar tabs to run laser star lights, getting quotes bare and plated.
Is there any modifications that members would like to see, other that going heavy wall thickness, OEM is too thin and dings easy.

My goal is to be sell them fro $85.00 plated /  $55.00 raw

OEM Front Bumper Plated
Logged
F Mitch Keller

Share on Bluesky Share on Facebook

Offline

  • Trade Count: (0)
  • Trail Blazer
  • ******
  • Posts: 645
Re: Interest On Making OEM Type Front Bumpers
« Reply #1 on: January 31, 2013, 12:10:11 pm »
I would take a raw no light tabs.

What year is the fatbar? 1987?

Bumper on ebay for 87 with padding. 20 + 12 shipping
Logged

Offline

  • Mitch Keller
  • Trade Count: (0)
  • Administrator
  • Trail Blazer
  • *****
  • Posts: 799
  • Love The Smell Of 927 and Race Fuel In The Morning
  • Location: Riverside Ca
Re: Interest On Making OEM Type Front Bumpers
« Reply #2 on: January 31, 2013, 12:15:25 pm »
1990
Logged
F Mitch Keller

Offline

  • Trade Count: (0)
  • Trail Blazer
  • ******
  • Posts: 776
Re: Interest On Making OEM Type Front Bumpers
« Reply #3 on: January 31, 2013, 06:02:55 pm »
It's be cool if you could make them a little wider like the Pro-Armor bull horn bumper... more protection for front end that way too....
Logged

Offline

  • Mitch Keller
  • Trade Count: (0)
  • Administrator
  • Trail Blazer
  • *****
  • Posts: 799
  • Love The Smell Of 927 and Race Fuel In The Morning
  • Location: Riverside Ca
Re: Interest On Making OEM Type Front Bumpers
« Reply #4 on: January 31, 2013, 06:30:56 pm »
Quote from: FX4Pitrone on January 31, 2013, 06:02:55 pm
It's be cool if you could make them a little wider like the Pro-Armor bull horn bumper... more protection for front end that way too....

How much wider?  wide enough to protect the front shocks? You dont want anything solid in the middle that could block airflow to the radiator scoop.
Logged
F Mitch Keller

Offline

  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 162
  • Gender: Male
  • Mix'in & Kick'in
  • Location: michigan
Re: Interest On Making OEM Type Front Bumpers
« Reply #5 on: January 31, 2013, 09:45:38 pm »
 fat bar  little wider on  top and a bar about as wide as the stock  oem top bar 6 inches below with teeth top and bottom  bars
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 33
Re: Interest On Making OEM Type Front Bumpers
« Reply #6 on: February 01, 2013, 09:42:40 am »
I would be up for a raw one.
Logged

Offline

  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 162
  • Gender: Male
  • Mix'in & Kick'in
  • Location: michigan
Re: Interest On Making OEM Type Front Bumpers
« Reply #7 on: February 01, 2013, 10:15:34 am »
Raw with teeth or just the bar  ranger? How wide Mitch ? Id say about 4 inches 2 inch on each side
Logged

Offline

  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 161
  • Gender: Male
Re: Interest On Making OEM Type Front Bumpers
« Reply #8 on: February 01, 2013, 05:28:08 pm »
1987 is the skinny bumper  with the  curves at the ends.
Logged
87  LT500R
98  sporstman500

Offline

  • Trade Count: (0)
  • Trail Blazer
  • ******
  • Posts: 645
Re: Interest On Making OEM Type Front Bumpers
« Reply #9 on: March 20, 2013, 04:06:59 pm »
whatever happened to this is this still going to happen Mitch
Logged
Pages: [1]   Go Up
« previous next »
 

+- Suzuki Quadracer HQ Store Zone

http://www.suzukiquadracerhq.com/index.php?action=store