+-
« previous next »
Pages: [1]   Go Down

Author Topic: Jetting question Zilla  (Read 824 times)

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 8
Jetting question Zilla
« on: May 21, 2013, 08:48:45 am »
.060 Over Wisco Piston
Paul turner exhaust
Carbon fiber reeds
Keihin 39mm Carb

Be doing mostly trail riding around 80 degrees. What jets should I run? Thanks
Logged

Share on Bluesky Share on Facebook

Offline

  • Trade Count: (0)
  • Range Rover
  • *****
  • Posts: 381
  • Gender: Male
  • Location: watertown ny
Re: Jetting question Zilla
« Reply #1 on: May 21, 2013, 09:54:39 am »
what elevation are u at or around? are u running air box or open filter
Logged

Offline

  • Trade Count: (0)
  • Forum Moderator
  • Elite Member
  • *********
  • Posts: 2058
Re: Jetting question Zilla
« Reply #2 on: May 21, 2013, 09:57:20 am »
So cal sea level
87.5 mm piston
Hpr19
39 pwk
Stock reeds
Airbox no lid

180 main
58 pilot
Dgh 4th clip from the top
6.0 slide

I cant give you specific jetting for your area, only what I'm running

Oops
Logged
87 HPR LT500
04 Roll LOBO II TRX250R
06 LTR450
87 LT500
85 & 86 LT250
86 & 87 TRX250R
07 & 09 Husqvarna TE450
00 CR125R

Offline

  • Trade Count: (0)
  • Weekend Warrior
  • ****
  • Posts: 162
  • Gender: Male
  • who brakes later is more quickly
  • Location: Germany
Re: Jetting question Zilla
« Reply #3 on: May 21, 2013, 12:50:04 pm »
I have the same Setup 87, 5 wiseco piston and a Paul Turner ex.
Is this really more different at the oem mic. to kei. ?

Logged
under-steers is when you see the tree the goes in. overrides is when you hear the tree which you were going on.
"Walther Röhrl "

Offline

  • Trade Count: (0)
  • Green Horn
  • ***
  • Posts: 56
Re: Jetting question Zilla
« Reply #4 on: May 21, 2013, 01:22:45 pm »
i had close to the same setup as you, and ran a 172 main, 55 pilot, dgh needle on 3rd clip. this was a keihin pwk39.
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 8
Re: Jetting question Zilla
« Reply #5 on: May 25, 2013, 07:24:04 pm »
I have a 200 main and 60. It doesn't hit powerband, Like its running to rich?
Logged

Offline

  • Trade Count: (0)
  • Elite Member
  • **********
  • Posts: 2209
  • Gender: Male
  • Location: ohio
Re: Jetting question Zilla
« Reply #6 on: May 26, 2013, 12:20:32 am »
either move needle clip or drop down in jet size.
once you find a jet that you think is the one then do the test. ride with 1/4 thrtl see what motor does. does it run away or load up.
then do half thrtl then full thrtl. if bike want to rev up then its lean, if it holds and runs smooth then your good. if it starts to load up then your rich.
i would try a 185 to 180, to start
Logged
life's journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sidays totally worn out shouting "HOLY SH*T...WHAT A RIDE!"

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 8
Re: Jetting question Zilla
« Reply #7 on: May 26, 2013, 08:15:40 am »
thanks GrkGuy should I change pilot also
Logged

Offline

  • Trade Count: (0)
  • Newbie
  • **
  • Posts: 18
Re: Jetting question Zilla
« Reply #8 on: June 11, 2013, 11:06:42 am »
60 pilot should be fine to start.
Logged

Offline

  • Trade Count: (0)
  • Elite Member
  • **********
  • Posts: 2209
  • Gender: Male
  • Location: ohio
Re: Jetting question Zilla
« Reply #9 on: June 11, 2013, 01:42:17 pm »
dont forget to make sure you have air screw at 2 turns out from closed.
Logged
life's journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sidays totally worn out shouting "HOLY SH*T...WHAT A RIDE!"
Pages: [1]   Go Up
« previous next »
 

+- Suzuki Quadracer HQ Store Zone

http://www.suzukiquadracerhq.com/index.php?action=store