Suzuki Quadracer HQ
LT250R Quadracer => LT250R - Engine => Topic started by: LT250RWV on December 28, 2012, 05:09:15 pm
-
anything after V2's suck. Zilla boots work, just need to match small and big reed and angled or straight.
-
Il check into getting some new v force reeds.What about the 4s.Also will a zillia boot work on the 250s for the bigger carb so you dont have to fight getting a 38 in a stock boot.
-
I like how Boyshen change the throttle respones on the bike.It seems to be more crisps threw all the ranges.I wonder how long it would take for them to get me Scp pipe ready and shipped.
Matt has a Chrome 250 pipe + shield ready to ship for $635. Boyessen Is restictive, it has ok low/mid response with old tech pipes like fmf. It is a worse cage thank stock with good reeds, Then add a big carb and pipe= JUNK..
-
I like how Boyshen change the throttle respones on the bike.It seems to be more crisps threw all the ranges.I wonder how long it would take for them to get me Scp pipe ready and shipped.
You could PM him.Think he goes by pipester on here.
-
As far as carbs I run a 38mm Mikuni TMX which works very well.Can get one off a Honda 02/03 CR250 for a decent price.
-
I like how Boyshen change the throttle respones on the bike.It seems to be more crisps threw all the ranges.I wonder how long it would take for them to get me Scp pipe ready and shipped.
-
Get rid of the RAD valve it is constictive, Put a stock cage with carbon tech reeds in it till you can get V2's. With the SCP/Q pipe your combo will rip.......... Might have to trim a little but you can still run dumbo ears.
-
So with some trail porting 38pwk Boyshen rad valve kn filter milled head .20 bored .80 over.So would it pull hard with these mods right now.I do alot of trail riding and need good midrange and low.Also would i have to cut my stock fenders to run this pipe.From the photos it looks tight in their.
-
Ice runs an SCP/Q 250 pipe. Low and mid is close to a PT, with way more top end >:D >:D >:D >:D >:D. He ports them to Plus The Big Bore he's working on +k2 >:D
-
Thanks Iceracer.Hey do you use Scp pipe.I was wondering how good it is also how would it compare to paul turner. Thats if you use it.Also dont you do port on these motors.I had a little done that was a joke .I had to knife edge the transfer ports myself.They just took a little material off .But i think i want it ported alot more.I was able to keep up with my friend trx450r. before Christmas.He got a bunch of stuff for it and hes young and he thinks 2 strokes are a joke and their noway they can complete.He was able to pull away from me the other day.That why i want to know whats is the best around pipe for lt250r. I like midrange also topend.But i dont want a pipe that is all topend.Everyone telling me the scp pipe is the best but no input on how it ride or where the power is in it.Thanks Brian
-
Properly set up a 38-39 on a 250 will make more power than a 34. Much larger than a 38 and you will will loose torque and ride ability. Depending on engine and pipe setup. A 36-41 is the optimum setup generally.
-
On the trx250r yes ...
On the Zilla I can't say since the pwk was on the quad when it was purchased. Some say that the mikuni carb is better, more tuning capability. I have a bunch of keihin jets & needles, so I'm more familiar when jetting.
-
Well did the 39 pwk give you a power edge over the stocker.
-
Someone here should be able to answer your question....
I'd try but I've only had 39pwk experience on a trx250r and a Zilla. So I'm not much help... _^_
-
What going on you post something and its seem to be a ghost page. <1>
-
Im running stock carb.Mods are Boyshen rad valve, milled head.20, Trail porting,Fmf pipe and silencer ,K n air filter, bored .80 over.My jetting is pilot is 35 stock needle 4 clip main 240 .It seems my pilot is still rich high rev point is 2 and half turns out.I put a 260 in it this evening and 1 st and 2nd wouldnt rev completely out but 3 threw 6 would.i 2000 feet is base and run up to 4000 feet .Also does the 38 pwk give you more power when adding them onto these quad.I have one brand new but i couldnt get it jetted right.But i had a air leak when i was trying it.I want to know is their a big difference in the bigger carb and worth the time of putting it on.Thanks