Suzuki Quadracer HQ

LT250R Quadracer => LT250R - General Discussion => Topic started by: 92lt250wannabe on March 19, 2015, 08:50:50 am

Title: Re: How to do Bump steer mod.
Post by: Rainman56 on May 03, 2015, 10:24:57 pm

Definitely need to reset the toe in.

Title: Re: How to do Bump steer mod.
Post by: Dutch_Rutter on May 03, 2015, 10:10:45 pm

Once you do the mod you do need to re-adjust the steering settings for it to be correct.

Title: Re: How to do Bump steer mod.
Post by: Izzo on May 03, 2015, 10:03:45 pm

So I did this mod. The bike Doesn't like to stay in a straight line. It's all over the place and follows grooves. I didn't ride it before doing the mod. I did notice the camber is positive And needs corrected. Do you guys think it's from the camber or the camber is part of it and it needs the toe too?

Title: Re: How to do Bump steer mod.
Post by: Izzo on April 04, 2015, 11:39:43 pm

Thank you.

Title: Re: How to do Bump steer mod.
Post by: Dutch_Rutter on March 29, 2015, 11:13:55 am

Just them bolt it back up like normal. Only difference is how these "horns" are facing instead of angled up they are angled down. to get even better steering one can also pick the camber shims up from Mitch, then you will have a very well handling LT.

Title: Re: How to do Bump steer mod.
Post by: Izzo on March 28, 2015, 09:53:50 pm

Do I have to flip the tie rods up side down and also on the end of the steering stem or do I just bolt it all back up after flipping the horns like you did.

Title: Re: How to do Bump steer mod.
Post by: 92lt250wannabe on March 20, 2015, 08:21:12 pm

I think this is pretty obvious on what has to happen.

Title: Re: How to do Bump steer mod.
Post by: GrkGuy on March 20, 2015, 04:10:28 pm

Do it again with a whit back ground.

Title: Re: How to do Bump steer mod.
Post by: 92lt250wannabe on March 19, 2015, 07:12:36 pm

I have no idea but I hope this clears the air on the bump steer confusion.

Title: Re: How to do Bump steer mod.
Post by: GrkGuy on March 19, 2015, 05:49:43 pm

Nice why didn't someone do this a long time ago.

Title: How to do Bump steer mod.
Post by: 92lt250wannabe on March 19, 2015, 08:50:50 am

In order to do the bump steer mod, the steering horns (where the tie rod end connects at the spindle) needs to be flip flopped from the left side to the right. They also will be flipped upside down. So instead of angling up they angle down. This will get the tie rod more parallel with the a arms. Here are some pictures to help everyone understand.

Stock setting

(http://i1138.photobucket.com/albums/n540/zjdlobik/FF18C376-3DF0-4E51-99D8-A18E5D2B4E02.jpg) (http://s1138.photobucket.com/user/zjdlobik/media/FF18C376-3DF0-4E51-99D8-A18E5D2B4E02.jpg.html)

Bump steer mod

(http://i1138.photobucket.com/albums/n540/zjdlobik/AE575572-34E9-47BE-A274-B4B106A13C5C.jpg) (http://s1138.photobucket.com/user/zjdlobik/media/AE575572-34E9-47BE-A274-B4B106A13C5C.jpg.html)