Author Topic: 1988 zilla (Read 2310 times)

Szillahickson · « **on:** August 30, 2017, 06:21:39 pm »

How's it going guys ,I recently got a 1988 zilla .my friend has one and I compared them I have a cooled head carbon fiber reeds inside silencer says fmf I'm assuming fmf there is a keihin carb on here I see that isn't stock but my jug has ct engraved in it can anyone tell me what jets I should be running and wat this ct means I feel sluggish off idle then it picks up and rips thanks

JDaivs1 · « **Reply #1 on:** August 30, 2017, 11:03:27 pm »

Call them they can give you an idea on jetting.

CT Racing

11805 Slauson Ave.

Santa Fe Springs, CA 90670-2219

Phone: (562) 945-2453

Fax: (562) 945-7006

Email: info@ctracing.com

Szillahickson · « **Reply #2 on:** August 31, 2017, 03:15:21 am »

Is there anything I should know about these year zillas or in general ,is there anything interchangeable from any other bike known problems etc ....

Szillahickson · « **Reply #3 on:** August 31, 2017, 04:12:41 am »

They won't let me post pics

Q2W · « **Reply #4 on:** September 05, 2017, 02:00:59 pm »

Welcome!

you'll need to use a hosting site like imgur to post pics.

Lots of known problems with these bikes. Best bet is search the forums as best as you can. Lots are stickied.

As far as jetting, what's in the carb now?

Szillahickson · « **Reply #5 on:** September 05, 2017, 02:24:27 pm »

170 main jet ,62 pilot jet , needle clip is moved one up from middle clip so second to the top this is how it came ,it's a keihin carb

Q2W · « **Reply #6 on:** September 06, 2017, 06:36:09 am »

62 pilot seems really big compared to your main. -quick observation not knowing your elevation, air box setup, porting, if carb has been bored, etc.

I ran that carb a long time ago. was bored to 41mm with an open airbox and mild porting at about 800ft and if i remember right i ran a 58/185.

You said it was doggy down low, my first hunch is you're rich on the pilot.

Will the bike idle? A quick test to see if your pilot is the right size is by adjusting the air/fuel mixture screw. (NOT the big thumb screw with the spring on it. It's a small flat head screw) Set the air/fuel to about 2 turns out. Start the bike and if it wont idle adjust it CW 1/4 turn a time. If you get below 1 turn out and the motor still hasn't held an idle, your pilot is too large. Put a size smaller pilot in and start the process over.

Szillahickson · « **Reply #7 on:** September 06, 2017, 09:30:46 am »

I'm at about 1600ft stock airbox with NO lid ,the jug got ct engraved on the sides ,carbon fiber reeds ,cool head .the kid I got the bike from sayin that it was built by cpe racing top and bottom said bored over honestly I think he is a load of **** he tryin to make it sound good because I traded him a beautiful running yamaha banshee .

Q2W · « **Reply #8 on:** September 08, 2017, 06:29:32 am »

yea, anything over about 1200ft will need to downsize the pilot. I think that's a great place to start. buy few smaller pilots and start stepping down from 62 until she spins like a top. good luck!

Szillahickson · « **Reply #9 on:** September 08, 2017, 07:18:11 am »

She still start 1 kick but I fill like the throttle ain't where it need to be ,I will def start there tho thank you

Rainman56 · « **Reply #10 on:** September 09, 2017, 07:29:31 pm »

What needle are you running?

Szillahickson · « **Reply #11 on:** September 10, 2017, 05:04:17 am »

I really can't tell the markings are all rubbed off

Szillahickson · « **Reply #12 on:** September 10, 2017, 01:41:40 pm »

What needle should I run for the keihin carb

Szillahickson · « **Reply #13 on:** September 11, 2017, 03:47:59 pm »

What's a good needle jet to get

Rainman56 · « **Reply #14 on:** September 12, 2017, 07:57:45 pm »

The Keihins don't have a changeable needle.Most guys find the DGH needle works well on the 500's.

Szillahickson · « **Reply #15 on:** September 13, 2017, 03:46:31 am »

That's good to know I would have tried to put needles in this bike for no reason ,thanks again I'll let you know how it turns out p

Rainman56 · « **Reply #16 on:** September 13, 2017, 04:07:48 am »

Quote from: Szillahickson on September 13, 2017, 03:46:31 am

That's good to know I would have tried to put needles in this bike for no reason ,thanks again I'll let you know how it turns out p

I meant to say the Keihins don't have changeable needle jets.....The needle that goes through the slide is changeable and most run the DGH needle.Sorry for mistype.

Szillahickson · « **Reply #17 on:** September 13, 2017, 04:44:03 am »

No prob that was my fault i was meaning the needle that go thru the slide thanks imma order one

Szillahickson · « **Reply #18 on:** September 16, 2017, 08:35:10 pm »

Fellas fellas fellas that needle and a small tune omg somthing different I wish in an show you guys in a vid how I fell

Rainman56 · « **Reply #19 on:** September 17, 2017, 06:13:25 am »

So it runs better? lol

Szillahickson · « **Reply #20 on:** September 17, 2017, 02:00:46 pm »

Yeah I put that dgh in there and she woke up like I never imagined my friend has a 87 zilla ssssssuuuuuuuuper jealous rite now

Szillahickson · « **Reply #21 on:** September 17, 2017, 05:53:21 pm »

My c clip on my needle is loose though I had her set one clip up from the middle and randomly started to bog I pulled out the slide and it feel all the to the bottom clip no wonder it was bogging down real bad hahaha

News:

Author Topic: 1988 zilla (Read 2310 times)

Suzuki Quadracer HQ Store Zone